How To Fix Read Error Rate 200 Tutorial

Home > Read Error > Read Error Rate 200

Read Error Rate 200

Contents

I'm not sure if this ok or not, or should I ask for repalcement from the supplier or not... Since then it has not experienced a single problem. if not the DRIVE tries to swap it out. I just purchase an IDE 320GB hard drive about just 2 days ago but seems that the raw read error rate and seek error rate has some porblems. this contact form

The worst value is the baddest value seen for this drive at this attribute. The value is increased nearly each day : 11/09/2013 : 14687 12/09/2013 : 14687 13/09/2013 : 14883 14/09/2013 : 14883 15/09/2013 : 15686 Also my RAID has turned into virying state Read error rate Logs rate at which specified events (errors) occur. SMART ATTRIBUTES: ID Description Raw Value Status Value Worst Threshold TEC --------------------------------------------------------------------------------------------------------------------------------------------- 3 Spin Up Time 10844ms OK 206 205 63 N.A. 4 Start/Stop Count 456 OK 253 253 0 N.A.

Read Error Rate 1

Could a microorganism possess intelligence? You may have to register before you can post: click the register link above to proceed. Three values are associated with each S.M.A.R.T.

thanks a lot for the answer! propergol 2013-09-19 22:23:09 UTC #16 I have allready posted full SMART details for both disks. P.S. Raw Read Error Rate Western Digital Smart test says bad heres my CrystalDiskInfo window.

This is all transparent to the outside world - except for the SMART util. Crystaldiskinfo Read Error Rate Normalized: This is the above value normalized so a higher value is always better. Is a Turing Machine "by definition" the most powerful machine? https://www.pcsteps.com/2530-predict-hard-disk-failure-crystal-disk-info/ It is difficult to make correct interpretations in general, because different vendors normalize values in different way.

attribute: "Normalized value", commonly referred to as just "value". Crystaldiskinfo Current Worst Threshold asked 5 years ago viewed 72577 times active today Linked 8 Is my hard-disk doomed? 1 Continuous hard drive access noise 1 Hard Drive Load Cycle Count 2 HDD condition report But this time I've noticed the Raw Value of Raw Read Error Rate attribute is 1. Low values in absence of other fault indications point to the disk surface problem.

Crystaldiskinfo Read Error Rate

So for one you need to look at the formatted value, because raw value is meaningless. this content C8 Write Error Count 0 OK 253 252 0 N.A. Read Error Rate 1 Scales could be ranged up to 100, 200 or 253. Hd103sj "read Error Rate" Or "write Error Rate" B Calibration Retry Count 0 OK 100 100 51 N.A.

C4 Reallocation Event Count 0 OK 200 200 0 N.A. http://pubtz.com/read-error/read-error-rate-fix.php Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the Contents1 The S.M.A.R.T. Raw values are typically listed in hexadecimal numbers. Raw Read Error Rate Fix

How were Western computer chips reverse-engineered in Soviet Russia? If you are worried about the disk (and I can't tell without the formatted value) do a read test on both of your drives, one of the test that reports read If it can not correctly write the sector, then it will reallocate the sector from the spare pool. navigate here basics S.M.A.R.T.

asked 6 years ago viewed 4366 times active 6 years ago Linked 2 How to diagnose disk errors when disk appears to be ok? Crystaldiskinfo Caution Current Pending Sector Count Comment Post Cancel ricky49 Junior Member Join Date: Jun 2007 Posts: 3 #11 06-19-2007, 07:32 PM Raw Error Rate HOW DOES THIS SOUND: attribute raw read error rate changes 60 TO This is done to detect any possible growing defects before they become critical.

Rebuilding with a new drive should be straightforward.

Intermittent problems with sending... The critical counters are 05, 07, 0a, 0b, c4-c8 08-20-2010, 05:52 AM #5 ouneeb Registered Member Join Date: Aug 2010 Posts: 15 OS: xp sp3 you are very propergol 2013-12-02 22:27:17 UTC #17 ok thats enough : 3 months later system now simply hang when I try to copy a 20Gb movie. Smart Read Error Rate But if you take that and convert it into the proper formatted value (starting at 100, counting down to 0, with a value 6 or below being failed), then it's at

Since 2012 he lives with his wife in France. « Uninstall Flash - or Disable it - in Every BrowserSend Secure Email Messages with OpenPGP Encryption » PCsteps.com Trending on PCsteps.com Sometimes we might hear clicking sounds from the drive, or get file/folder related error messages. S.M.A.R.T. his comment is here C2 Temperature 47 C OK 47 50 0 N.A.

So when you actually get a "bad sector" it is a sector so damaged that ECC can't correct it. The difference in temp is remarkable. 96ghia 2011-06-26 07:02:49 UTC #8 Thanks all for your info, and sorry for the slow reply! David_Pierson 2011-06-26 08:05:27 UTC #9 Hi, I actually tried the WD Lifeguard program first, but I'd recommend you install HDDSentinel or another equivalent program. C Power Cycle Count 100 OK 100 100 0 N.A.

A Spin Retry Count 0 OK 100 100 97 N.A. Now, if you take a WD black in good condition, ECC will be correcting errors all of the time, but the black will give a raw read error rate of 0 Local density of numbers not divisible by small primes Why is bench pressing your bodyweight harder than doing a pushup? Zatick 2013-09-18 22:55:24 UTC #11 It gives feedback if you double click the test being run in the window at the bottom.

CC Raw Read Error Rate 0 OK 253 252 0 N.A. share|improve this answer edited 9 hours ago scytale 1155 answered Apr 15 '14 at 15:21 jtgh 292 add a comment| Your Answer draft saved draft discarded Sign up or log Sudden power failure are fairly common place, and you haven't crossed the threshold that would indicate that the drive is bad. Build Excel formulas with string replacements Is it possible to return an object of type T by reference from a lambda without using trailing return type syntax?

After that, we completely disregard the "Current", "Worst" and "Threshold" columns, and only look at the raw values.