Fix Range Error Code F11 Tutorial

Home > Error Code > Range Error Code F11

Range Error Code F11


George // Dec 22, 2014 at 3:32 pm Hi Gene, thanks I really appreciate your time. So we were back to blaming the EOC. It is giving F11 error. When I replace the EOC again do you think I need to be concerned with the Molex connectors for the temp probes on both ovens? Check This Out

The part number for the temperature probe is 316490000 If the reading is normal, the EOC has failed and would need to be replaced. Ken // Dec 29, 2014 at 9:59 am Hello Gene, Thank you, you always answer quickly. Please check back in a few minutes. If the motor does not rotate, replace lock motor assembly.

Frigidaire Oven F11 Error Code

For what it's worth, it seems like the "conv bake" button is ultra sensitive especially when the oven is hot. The part number for the temperature probe is 316490000 Good luck. Keep me posted. Thank you for your question.

Ken // Dec 28, 2014 at 1:36 pm Hello Gene, Thank you for the info.. What can I do to repair it??? tks. 3 answers Popular Products in Frigidaire Frigidaire FGMC3065PB Gallery 4.6 cu. When replacing a potentiometer, do not over-tighten the hex nut. Frigidaire Range Error Codes Shorted Probe connection. 1. (F30 or F31) Check resistance at room temperature & compare to **RTD Sensor resistance chart.

Could you please explain what this is. Frigidaire Gas Range F10 Error Code Remove the power from the oven and pull the oven out of the cabinet. 12.667 görüntüleme 7:11 Duet Washer Motor Test - Süre: 3:05. what is a speed bake switch?

The cause of the problem can be a failed lock motor switches or a failed EOC. F11 Error Code Electrolux Range Tina Jan 02, 2014 Will the oven still work or did it only stop the beeping? This particular control panel was designed for this model only. F90 F91   F92   F93 F94 Maximum oven door unlock time exceeded.

Frigidaire Gas Range F10 Error Code

The ribbon cable will then slide right out.) Use a razor blade to gently work your way around the plastic trim bezel and remove the bezel. Older products will show only two digits F-codes, but on ranges manufactured beginning in 2004 many of EOC's will have expanded three digit fault codes. Frigidaire Oven F11 Error Code We've only had the range for 11 months. Eoc Frigidaire Oven she gets error code 11.

If you would like to replace it too, I need one more letter from the model number to get the correct part number for you. his comment is here Also the model number you sent is incomplete. The part number for the oven relay board is 316443920 The part number for the EOC is 316576601 Good luck. Mush to our dismay, the F11 error still occured. Kenmore Stove F11 Error Code

I you have a service technician complete the repair, then the labor will probably cost around $150. The part number for the EOC is 316557115 Good luck. Severe overheating may require the entire oven to be replaced should damage be extensive.  2. (F11, 12 & 13) Disconnect power, wait 30 seconds and reapply power. 3. (F11, 12 & It would need to be replaced.

Wire nuts (pack of 10) AP5641944 Good luck and keep us posted. Frigidaire Stove Keeps Beeping Inspect the overlay. I am getting this number directly from the oven , not the paperwork.

If in spite of everything it would not fix the problem, you can return it to within 365 days.

You can get them in a hard ware store or order from by clicking on the following part number. I found them for you: "Each oven temperature can be individually adjusted. Any ideas what is wrong? Frigidaire Oven F10 Reset I will show you how to diagnose and fix them depending on the fault code.

Anonymous May 04, 2009 what is a speed bake switch? F62 Missing zero-cross signal Replace the EOC. Most likely the problem is a faulty EOC. navigate here i hope this will help with your range issue. 1 Share theConversation Click to Chat We're available to chat FAQs Check out the most frequently asked questions Video How to use

Ed Gene // May 6, 2015 at 9:35 pm Hi Ed, Put everything back together and give it a try. later it starts beeping and F1 code An F1 error code indicates a faulty keypad and /or ERC electronic control. Power up the stove. It is self-adhesive.

What does this mean please? We ordered both the parts, tried the EOC first, with no fix. You can change this preference below. Geri al Kapat Bu video kullanılamıyor. İzleme SırasıSıraİzleme SırasıSıra Tümünü kaldırBağlantıyı kes Bir sonraki video başlamak üzeredurdur Yükleniyor... İzleme Sırası Sıra __count__/__total__ error f11 i disagree Abone olAbone olunduAbonelikten çık3636 Yükleniyor...

darlene // Dec 19, 2014 at 7:03 pm The frigidaire stove my son has has a f10 code. Also, just a side note I have purchased various parts from over the years and have always been very happy, top notch business. The wires look OK (no visible external wear) from the plastic connector in the back of the EOC module down to the metal bracket holding the RTD temperature sensor into the The new one should solve it.

Gene. Based off the information you have provided your Frigidaire range is displaying an error code of "F11". dave // Nov 18, 2013 at 6:16 pm Gene. I placed my order for the needed EOC today.

Please check back in a few minutes. I ran the self clean on my electrolux and within 2 weeks of using my oven again, I had the F10 runaway temperature alarm.